PVDF Film Arterial Pulse Sensor
Flexible 28 μm piezoelectric transducer element with screen-printed silver ink electrodes.
Biomedical Engineering / Piezoelectric Pulse Transducer
FREE TO EXPLORELABORATORY 03 · BIOMEDICAL ENGINEERING
Piezoelectric Sensor Charge Output & Arterial Pulse Sensitivity
Determine the dynamic piezoelectric voltage generation and charge sensitivity of a PVDF film transducer under simulated peripheral arterial pressure pulses. Explore interactive physiological instrumentation simulation, biomechanics, and biomedical engineering telemetry.
BIOINSTRUMENTATION · BIOSIGNALS · BIOMECHANICS · IMAGING
Your virtual biomedical engineering laboratory.
PEAK SENSOR VOLTAGE V_P—
PHYSIOLOGICAL & TEST CELL TELEMETRY
Ready to sample with Pulse ΔP = 6.0 kPa.
Adjust Pulse ΔP, then execute biomedical trial.
Biomedical engineering telemetry and physiological states are evaluated rigorously using 64-bit IEEE 754 precision. Residuals reflect ordinary least-squares regression across successive observations. Continuous data structures support high-fidelity biological and physiological modeling.
Biomedical assumptions and boundary condition limits
The linear sensitivity model applies across the physiologic pulse range (2.0 to 12.0 kPa). Evaluated using a 28 μm metallized PVDF polymer sensor element coupled to a high-input-impedance JFET charge amplifier (time constant τ = 2.5 s). Dynamic pulsation frequency standardized at 1.2 Hz (72 beats/min) simulating resting radial arterial pulses.
Biomedical apparatus & physiological sensors.
Hydraulic Radial Artery Pulsation Phantom
Provides compliant silicone artery embedded in tissue-mimicking phantom driven by pulsatile pump.
Electromagnetic Pulsatile Piston Pump
Generates physiological pressure pulse waveforms with adjustable pulse pressure from 2 to 12 kPa.
Precision Disposable Blood Pressure Transducer
Monitors internal lumen pressure pulses with NIST-traceable piezoresistive reference.
Low-Noise High-Impedance Charge Amplifier
Converts sensor charge into proportional voltage without low-frequency signal droop.
Dual-Channel Digital Storage Oscilloscope
Captures peak voltage V_p and pulse transit morphology at 1.0 kHz sampling rate.
FOLLOW THE METHOD
A reason behind every step.
Determine the dynamic piezoelectric voltage generation and charge sensitivity of a PVDF film transducer under simulated peripheral arterial pressure pulses. Standardized parameter settings: 2.0, 4.0, 6.0, 8.0, 10.0, 12.0 kPa.
01
Arterial Phantom Priming and Pressure Calibration
Prime the silicone radial artery phantom with degassed physiological saline and calibrate the inline reference pressure transducer to read true systolic and diastolic pressures.
02
Sensor Placement and Pre-Load Application
Position the PVDF pulse sensor over the superficial arterial phantom site with an elastic strap establishing a baseline contact pre-load of 2.0 kPa.
03
Pulsatile Waveform Standardization
Set the pulsatile actuator to resting heart rate cadence (72 BPM, 1.2 Hz) and establish an initial pulse pressure amplitude ΔP of 2.0 kPa (15 mmHg).
04
Peak Voltage Telemetry Acquisition
Capture 10 consecutive pulse cycles on the digital oscilloscope and record the ensemble-averaged peak-to-peak output voltage V_p in millivolts.
05
Pulse Pressure Progression
Increment dynamic pulse pressure amplitude through 4.0, 6.0, 8.0, 10.0, and 12.0 kPa, logging peak piezoelectric voltage at each stage.
06
Sensitivity Regression Analysis
Plot peak voltage V_p against pulse pressure ΔP, performing linear regression through the origin to determine pressure voltage sensitivity k_p.
YOUR NOTEBOOK · 0 OBSERVATIONS
Turn measurements into biomedical engineering insight.
Points are your recorded observations. The solid regression line validates Piezoelectric Pulse Transducer mathematical scaling.
LINEAR REGRESSION FIT · y = mx + b
V_p = k_p · ΔP = 14.2000 · ΔP
| # | Pressure Pulse Amplitude ΔP (kPa) | Peak Sensor Voltage V_p (mV) | Pressure pulse amplitude ΔP (kPa) | Peak sensor voltage V_p (mV) | Remove |
|---|
No readings yet. Execute a biomedical trial and record it.
Calculate it yourself.
CHECK YOUR UNDERSTANDING